| |
|
Technical References |
| |
|
|
|
|
| |
|
1.0 |
|
轴承PV值 PV value of Bushing |
| |
|
1.1 |
|
定义和容许的最高PV值 Definition and Max permissible PV value ► |
| |
|
|
|
|
| |
|
2.0 |
|
轴承的尺寸设计 Design of bushing's dimensions |
| |
|
2.1 |
|
轴承的内径 Bushing's I. D. ► |
| |
|
2.2 |
|
轴承的壁厚 Bushing's thinckness ► |
| |
|
|
|
|
| |
|
3.0 |
|
相配座孔的设计 Design of the mating housing |
| |
|
3.1 |
|
直套轴承 Cylindrical bushing ► |
| |
|
3.2 |
|
翻边轴承 Flanged Bushing ► |
| |
|
3.3 |
|
轴承倒角 Bushing's Chamfer ► |
| |
|
|
|
|
| |
|
4.0 |
|
相配轴的设计 Design of the mating shaft |
| |
|
4.1 |
|
直套轴承的安装 Straight set of installation on mating shaft ► |
| |
|
4.3 |
|
相配轴的表面粗糙度 Surface roughness of mating shaft ► |
| |
|
4.4 |
|
相配轴的硬度 Hardness of mating shaft ► |
| |
|
4.5 |
|
相配轴的表面处理 Surface treatment of the mating shaft ► |
| |
|
4.6 |
|
相配轴的结构设计 Structural design of the mating shaft ► |
| |
|
|
|
|
| |
|
5.0 |
|
轴承的使用寿命的计算 Calculation of bushing's service life ► |
| |
|
|
|
|
| |
|
6.0 |
|
轴承装配的过赢量的计算 Calculation of interference for bushing fixing ► |
| |
|
|
|
|
| |
|
7.0 |
|
轴承装配后的内径计算 Calculation of bushing's I. D. after fixing ► |
| |
|
|
|
|
| |
|
8.0 |
|
轴承装配后的配合间隙的计算 Bushing's clearace calculation after fixing ► |
| |
|
|
|
|
| |
|
9.0 |
|
轴承的装配 Bushing fixing |
| |
|
9.1 |
|
装配时压入力F的计算公式 Calculation of pressing-in force ► |
| |
|
9.2 |
|
装配方法 Fixing methouds ► |
| |
|
9.2.1 |
|
直套轴承的装配方法 Fixing methods for cylindrical bushings ► |
| |
|
9.2.2 |
|
翻边轴承的装配方法 Fixing methods for flanged bushings ► |
| |
|
9.2.3 |
|
止推垫片和滑板的装配方法 Fixing methods for thrust washers and slide plates ► |
| |
|
9.3 |
|
轴承装配后的内径校准 I.D. alignment after bushing fixed ► |
| |
|
9.3.1 |
|
卷制轴承的内径校准 I.D. alignment for common bushings ► |
| |
|
9.3.2 |
|
相配轴的校准 Alignment of the mating arbor ► |
| |
|
|
|
|
| |
|
10.0 |
|
初始装配后轴承的维护 Bushing maintenance after initial fixing ► |
| |
|
|
|
|
| |
|
11.0 |
|
轴承的储存 Bushing's Storage ► |
| |
|
|
|
|
| |
|
12.0 |
|
卷制轴承的检验方法 Inspection methods of wrapped bushings |
| |
|
12.1 |
|
卷制轴承的外径的检测方法 Inspection methods for bushing's O.D. ► |
| |
|
12.1.1 |
|
加压检测法 Load Checking (DIN1494-2 inspection A) ► |
| |
|
12.1.2 |
|
环规检测法 Measurement by GUAGE (DIN1494-2 inspeciton B) ► |
| |
|
12.1.3 |
|
带尺检测法 Measurrment by RULE (ISO3574-2 inspection D) ► |
| |
|
12.2 |
|
卷制轴承的内径的检测方法 Inspection methods for bushing's I.D. ► |
| |
|
12.2.1 |
|
塞规检测法 Measurement by Plug Guage (DIN1494-2 inspeciton C) ► |
| |
|
12.2.2 |
|
壁厚千分尺检测法 Wall thickness measuring by Micrometer (DIN1494-2) ► |
| |
|
12.3 |
|
止推垫片的检测方法 Test methods for thrust washers ► |
| |
|
|
|
|
| |
|
13.0 |
|
表面粗糙度对照表 Surface roughness table ► |
| |
|
|
|
|
| |
|
14.0 |
|
常用硬度值对照表 Common used hardness comparison form ► |
| |
|
|
|
|
| |
|
15.0 |
|
轴径公差表 Shaft tolerance table (ISO standard) ► |
| |
|
|
|
|
| |
|
16.0 |
|
座孔公差表 Housing tolerance table (ISO standard) ► |
